Visaton WS 25 E 8 Ohm, 10 Inch, HiFi Woofer
Quantity discounts
Buying in quantity?
Contact us with the quantity you need and we can discuss pricing for your order.
Request a quantity quoteDescription
The WS 25 E has a coated paper cone, a rubber surround and an extended rear pole plate for long excursions, and its basket shape makes it a practical replacement for the woofer in many standard hi-fi speakers. This 8 Ω version takes 80 W rated power, resonates at 34 Hz and fits a 225 mm cut-out.
Typical applications
- Replacement hi-fi woofer
- Large multi-way speaker systems
Full specifications
| Rated power | 80 W |
|---|---|
| Maximum power | 110 W |
| Nominal impedance | 8 Ω |
| Frequency response (−10 dB) | fu–6000 Hz (fu: lower cut-off depends on the cabinet) |
| Mean sound pressure level | 88 dB (1 W/1 m) |
| Excursion limit | ±6 mm |
| Resonance frequency fs | 34 Hz |
| Magnetic induction | 1.0 T |
| Magnetic flux | 310 µWb |
| Height of front pole-plate | 4 mm |
| Voice coil diameter | 25 mm |
| Height of winding | 15 mm |
| Cut-out | 225 mm |
| Net weight | 1.25 kg |
| D.C. resistance Rdc | 5.9 Ω |
| Mechanical Q factor Qms | 2.82 |
| Electrical Q factor Qes | 2.92 |
| Total Q factor Qts | 1.43 |
| Equivalent volume Vas | 113 l |
| Effective piston area Sd | 346 cm² |
| Dynamically moved mass Mms | 33 g |
| Force factor Bxl | 3.8 Tm |
| Inductance of the voice coil L | 0.8 mH |
| Terminals | 5.2 x 0.8 mm (+)/2.8 x 0.8 mm (-) |
Dimensions and drawings

Dimension drawing · Open original image
Installation and cabinet guidance
Allow a 225 mm panel opening. The frame is not round: it measures 245 mm across the flats and 283 mm across the corners, with 6 mm fixing holes set out at the corners on a 262 mm circle, so mark them from the driver itself. Behind the panel the driver needs about 106 mm of clear depth for the basket and the 80 mm magnet, with room beyond that for the terminals and the wiring.
Mount it on a rigid baffle with a continuous gasket or sealing strip between the frame and the panel. The pressed flange is thin, so tighten the fixings evenly and only enough to seal, and keep the cone and the rubber surround clear of the grille and of any internal bracing. The terminals take 5.2 x 0.8 mm blades on the positive side and 2.8 x 0.8 mm on the negative, so check blade width before choosing connectors, observe polarity and use an amplifier or crossover suited to the 8 Ω load.
The lower cut-off depends on the enclosure volume and tuning, so test the driver in the intended enclosure at the intended listening level before finalising the cabinet.
If it is going in as a replacement, check the cut-out, the fixing pattern, the depth behind the panel and the impedance against the original driver before ordering.
Related Products
Part no. 9046
Visaton W 165 A 2 Ohm, 6.5 Inch, Weatherproof Woofer
Part no. 2001
Visaton FRS 8 M 8 Ohm, 3.3 Inch, HiFi Full Range Speaker
Part no. 9089
Visaton M 10 8 Ohm, 4 Inch, HiFi Midrange Driver
Part no. 1055
Visaton WS 17 E 8 Ohm, 6.5 Inch, HiFi Woofer
Part no. 1054

