Visaton W 170 8 Ohm, 6.5 Inch, HiFi Woofer
Product photo · Enlarge image
Product photographs and manufacturer drawings. Images are not to scale.
Quantity discounts
Buying in quantity?
Contact us with the quantity you need and we can discuss pricing for your order.
Request a quantity quoteDescription
The W 170 is a straightforward, good-value 17 cm woofer for simple two-way speakers, car rear tray installations and replacement duty in finished hi-fi speakers. This 8 Ω version takes 40 W rated power, resonates at 57 Hz, gives 87 dB sensitivity from a 25 mm voice coil and has a mechanical excursion limit of ±7.5 mm.
Typical applications
- Two-way hi-fi speakers
- Car audio installations
- Replacement hi-fi woofer
Full specifications
| Rated power | 40 W |
|---|---|
| Maximum power | 70 W |
| Nominal impedance | 8 Ω |
| Frequency response (−10 dB) | fu–6000 Hz (fu: lower cut-off depends on the cabinet) |
| Mean sound pressure level | 87 dB (1 W/1 m) |
| Opening angle (-6 dB) | 54°/4000 Hz |
| Excursion limit | ±7.5 mm |
| Resonance frequency fs | 57 Hz |
| Magnetic induction | 1.0 T |
| Magnetic flux | 240 µWb |
| Height of front pole-plate | 3 mm |
| Voice coil diameter | 25 mm |
| Height of winding | 7 mm |
| Cut-out | 146 mm |
| Net weight | 0.77 kg |
| D.C. resistance Rdc | 7.2 Ω |
| Mechanical Q factor Qms | 2.92 |
| Electrical Q factor Qes | 0.9 |
| Total Q factor Qts | 0.69 |
| Equivalent volume Vas | 24 l |
| Effective piston area Sd | 137 cm² |
| Dynamically moved mass Mms | 8.7 g |
| Force factor Bxl | 5.0 Tm |
| Inductance of the voice coil L | 0.9 mH |
| Terminals | 4.8 x 0.8 mm (+)/2.8 x 0.8 mm (-) |
Dimensions and drawings

Dimension drawing · Open original image
Installation and cabinet guidance
Allow a 146 mm panel opening for a 170 mm frame, with the fixing holes on a 159 mm circle as 5 x 7 mm slots. Behind the panel the driver needs about 63 mm of clear depth for the basket and the 80 mm magnet, with room beyond that for the terminals and the wiring. The slots give a little adjustment, so mark them from the driver itself rather than working to a nominal pitch.
Mount it on a rigid baffle with a continuous gasket or sealing strip between the frame and the panel, and tighten the fixings evenly and only enough to seal so the frame is not pulled out of shape. Keep the cone and the surround clear of the grille and of any internal bracing. The terminals take 4.8 x 0.8 mm blades on the positive side and 2.8 x 0.8 mm on the negative, so blade width identifies polarity; observe it and use an amplifier or crossover suited to the 8 Ω load.
The lower cut-off depends on the enclosure volume and tuning, so test the driver in the intended enclosure at the intended listening level before finalising the cabinet.
If it is going in as a replacement, check the cut-out, the fixing pattern, the depth behind the panel and the impedance against the original driver before ordering. On a car rear tray, also check that the space behind the panel stays clear once the boot is loaded.
Related Products
Part number 1301
Visaton AL 130 8 Ohm, 5 Inch, High-End Midrange Driver
Part number 1305
Visaton AL 130 M 8 Ohm, 5 Inch, High-End Midrange Driver
Part number 1302
Visaton AL 170 8 Ohm, 6.5 Inch, High-End Midrange Driver
Part number 1281
Visaton AL 200 8 Ohm, 8 Inch, High-End Woofer
Part number 1263
Visaton B 100 6 Ohm, 4 Inch, High-End Full Range Speaker
Part number 1350
Visaton B 200 6 Ohm, 8 Inch, High-End Full Range Speaker
Part number 1261
Visaton B 80 8 Ohm, 3.3 Inch, High-End Full Range Speaker
Part number 2530
Visaton BF 30 R 4 Ohm, 1.2 Inch, Full Range Miniature Speaker
Part number 2243
Visaton BF 32 4 Ohm, 1.3 Inch, Full Range Miniature Speaker
Part number 2242
Visaton BF 32 8 Ohm, 1.3 Inch, Full Range Miniature Speaker
Part number 2249
Visaton BF 32 S 4 Ohm, 1.3 Inch, Full Range Speaker
Part number 2247